Sewing With An: Decorative Flag Garland


How To Make A Flag Garland

Last month it was my daughters birthday and I put up a paper flag garland. I’ve been using it already a couple of birthdays and now it’s time to throw it away… and make a garland that lasts and is pretty. This is a project that has been on my to do list for a while.. let’s get to it 😃

In this blog post I’ll show you how to make a flag garland out of scraps. In this project I make my own bias tape and show you how that can be easily done with a small tool, appropriately called a bias tape maker. You’ll see that this is a perfect project to make your own bias tape for the first time. I upcycled a used an old sheet for my bias tape.

You'll Need:

  • Fabric for the bias tape, I used an old white sheet, sized 34 by 34 inch, which gave me more than 7 yards of 1-inch wide tape. 
  • Colorful cotton fabric, you can use leftover scrap fabric or buy some nice fabrics that match well. I used scraps so it’s difficult to say how much you’ll need. I made 37 flags, the triangles are 6 by 8.5 inch without seam allowance, you need 2 triangles for one flag so you can cut approximately 24 flags out of 1 yard of fabric, so 48 triangles… 

 

First cut the triangle pattern out of a piece of cardboard, a triangle, the pattern is available as a download below.

Then take your fabric and start cutting, I started with my scissors but finally used my rotary cutter, you can cut 2 pieces at the same time if you want.  Don’t forget to add 1/4 inch seam allowance. If you don’t you’ll have smaller flags. You will need 2 pieces for 1 flag: one for the front and one for the back. So 24 flags mean you need 48 pieces and I needed 74 pieces for my 37 flags.

Sew the long sides at 1/4 inch seam. If you want you can pin the 2 pieces together before sewing.  Leave the short side open for turning later on.

Turn each triangle right side out again. I used a crochet needle to get the point pushed out.Then press the triangles to flatten the seams and remove any possible little puckers so you get a nice, flat, well-shaped triangle.

Now it is time to make the bias tape, or when you buy some ready-made, you can skip this part 😃

How to cut the fabric? 

Take your fabric and cut it to the biggest rectangle possible, fold it in half so you’ll get 2 triangles, then cut them with your scissors, and fold them to cut the strips with your rotary cutter and ruler

It’s important to cut the fabric on the bias rather than parallel to the fabric. The bias is the diagonal line in the middle if you cut it like this your tape has more stretch. It will be easier to use around curves, it will stay flat and won’t pucker.

Cut your strips 2 inches wide for 1-inch wide bias tape The first strips will be the longest, the next one shorter and so forth. Stop when the strips become too small.

Now we’re going to sew all these strips together and pull them through the bias tape maker to turn them into homemade bias tape.

To sew the strips together, you have to put them in a 90-degree angle, right sides together and let each strip overhang about a quarter of an inch. That’s because we're going to sew with a quarter of an inch seam allowance.

Sew right down on the red line

Cut that little overhang of fabric right off and press the seams open And now we got a nice long strip of fabric 2-inch wide fabric.

Just continue like this with the rest of your strips until you have the length you need.

Take your bias tape maker, I used the biggest one in my setA 1-inch wide bias tape maker actually makes 1/2 inch wide double-fold bias tape. Take the bias maker, put the strip in it, pull through and iron over it, easy! The result is a single fold 1 inch wide bias

When you come to a seam, don’t worry, just pull and iron.

If you want double fold, fold the bias tape in half and press with your hot iron.

Then start pinning your flags to the inside of the bias tape. Trim all corners and threads to clean it up before you finish off. Open the bias tape, put the short end of the flag inside and attach them with a Pins and clips.

This is the fun part where you can think about the color matching and the patterns!

Sew the entire open edge from end to end, closing the bias tape. Check regularly if you have both front and back while sewing.

Visit our SHOP for MORE AMAZING ITEMS AVAILABLE!

Credits: https://madamsew.com/blogs/sewing-blog/sewing-with-an-decorative-flag-garland

ONLY FOR THE FIRST 500 READERS:

Use the coupon code SPRING20 at checkout to get 20% off all orders! 

Only for the first 500!


Leave a comment